top of page
Writer's pictureDuane Inglin

The Ultimate Steelhead RAG



Fishing rags for Steelhead has been around actually longer than I have been fishing for Steelhead. Some guys have told me they where fishing rags back in the 1960’s. My Dad started fishing rags on the Puyallup and Carbon River back in the eighty's. I’m not sure where he saw it, or came up with it, but it was a Styrofoam and yarn combination that he swore by.

At some point, backer-rod was the simple go-to method to create the rag body. One cut and you had a nice small piece of foam to pull the yarn through.


Today, and for quite some time now, rags are tied on leaders, packaged and sold in sporting good stores pretty much everywhere. Most of the manufactured rags are white-bodied and usually have one or two colors of yarn pulled through them.

I gave up on the backer-rod about ten years ago. If I could find colored foam, that is what I would use. Walking through Target one summer, I stopped in the toy section and stood and stared at the big box filled with pool noodles. There were about six different colors in the box but the colors that made the most sense to me where Orange, Pink and Chartreuses/Green. I’ve also experimented over the years with any type of colored foam I could get my hands on. Some are tough and spongy while others are light and brittle. You won’t know until you try to cut it and then pull yarn through.


Colored rag bodies just makes, too much sense. Over the years, I have found that they work great for both Steelhead and Salmon. I pretty much rely on the Pink and Orange for Steelies. I use Green or Pink for Salmon. When I say Salmon, I can honestly say that I have caught, Kings, Coho and Chum on “Rags & Eggs”.





The other key component in your rag construction is the yarn. I use a lot of the Glo Bugs yarn. They have so many colors to choose from, it’s durable and they now have a lot of colors in UV.









When it comes to Steelhead, color selection is key. Even though Dad, back in the day, would use white backer rod he would use anywhere from four to six colors of yarn. The key here is color contrast. Steelhead are very visually stimulated. Light and dark colors in combination create contrast that they pick up on. It also helps to put colors together that replicate natural food that they feed on.




Think about the different colors in a Sand-Shrimp. Pinks, orange, purples a little black and the guts inside a sand shrimp are that brighter yellow. Those are pretty much the basic go-to colors for my Steelhead rags. I will mix in some Steelhead peach or at times a brighter pink or cerise. Usually its six colors with a single dark color mixed with two lighter colors in each combination; “contrast”.

With the size of the Glo Bug yarn, I will cut to length and then separate each piece length wise to make it thinner. To try and pull a full size piece of the yarn through the foam, is just a little too thick.


To create or punch out the rag body, it’s really pretty simple. First take your pool noodle and cross cut off a disc or round. The wider you make the disk you cut off, the longer your rag body will be. Next take a three to four inch piece of copper 3/8th in. water pipe. Take a small file and sharpen one end of the pipe, inside and out, until you get a sharp edge. When pushing the sharpened end of the tool against the foam and slightly twisting it back and forth, it will cut right through the foam. Using a pencil to push the cut plug of foam out of the tool works well.



Next, grab one of your yarn color combinations and pull it through the foam. This is easy to do with a needle and a piece or braided fishing line tied in a loop. Something else that works really well for pulling yarn through the foam is a Fly Bobbin Threader. Push the threader through the foam, place one end of the yarn pieces into the threader and pull it through the foam.



I pull the first three pieces of yarn through the foam. With the three short pieces laid together, you can easily pull it through the foam as long as you grab the very end of the yarn to pull it through. The more the yarn doubles up in the loop of braid, the bulkier it is to pull through the foam.

When I push the needle through for the second yarn grouping, I place it in the foam, just below the first layer of yarn. I don’t want to try to pull yarn through yarn, it won’t work.



Once I have both sets of yarn pulled through, I’ll pull and separate the pieces of yarn and spread them out around the body of the foam. Then I’ll cut and trim the yarn to length.








The final step is to simply tie your leader and thread the rag on to it. Push the needle through the body of the rag from bottom to top. Make sure you put a bead above your hook, before threading on the rag. This helps to keep the eye of the hook from punching up into your rag. Without the bead, you’ll go through a lot of rags in a day if the foam is tearing because of the hook.




Tie yourself a leader roll full of rags and go chase some Winter Steelies. Eggs and Rags or Rags with sand-shrimp tails are both hard combinations to beat. For me, Float-Doggin Rags with bait, with Steelie-Green water conditions, is a definite Go-To…


Duane Inglin

Comentarios


bottom of page